ATM MultiSwitchThe modular ATM "MultiSwitch" was designed in joint cooperation with a renowned manufacturer of ATM routers. MultiSwitch devices allow simultaneous communication of several voice and/or data channels via an optical media, or using optical radio relay systems. Communication is possible via company-owned singlemode as well as multimode optical fiber. Particular emphasis has been placed on modularity to maximize flexibility, while protecting the network infrastructure investment. The result is the ATM MultiSwitch 30/xM. This multiple use access system offers many switching possibilities: Ethernet, Token Ring 16, G.703 and ISDN. Which of the link interfaces will be used is defined by the selected software application and the user requirements. The ATM-MultiSwitch is either a fully integrated desktop model (including power supply) or alternatively a 19" MultiRack model. Applications Application 1: Connection via optical freespace transmission Application 2: Freespace transmission as a backup solution
Interface Modules In its base platform, the ATM MultiSwitch provides a 25.6 Mbps interface. Switching between LINK and ports is done via three modular interface cards that take over the routing and switching functions. The minimum delay caused by the switch is 10.8 mmsec. Three levels of priority (high, medium, low) are provided for data transport to assure prioritization of traffic.
The plug-in software module determines the bandwidth of the LINK interface which is a standard 25.6 Mbps for the ATM MultiSwitch. By means of extension modules, additional types of interfaces can be used: SDH/SONET 155 Mbps single or multimode fiber and balanced cat. 5 cable, DS-3/45 Mbps, E-3/34 Mbps, as well as E1/T1 2 Mbps/1.5 Mbps. User InterfacesEthernet/Fast Ethernet The ATM MultiSwitch has two switch ports for 10 Mbps Ethernet (twisted pair with RJ45 plugs, full and half-duplex). The connected variant is detected automatically (autodetect). Ethernet frames are transmitted via ATM AAL5.
E1/G.703/G.704 In addition to the Ethernet ports, two 2-Mbps E1/T1 interfaces (four-wire, RJ 45) are provided for connection of private telecommunications switching systems (PABX). E1/T1 data are transported via ATM AAL1. Narrowband ISDN D channel support is provided. For supporting the distribution of a synchronous clock via an ATM network, the ATM MultiSwitch offers two procedures: SRTS (synchronous residual time stamp) or adaptive clock recovery. The set up of a synchronous network is supported by distributed clock routing.
Network Management As an option, the ATM MultiSwitch offers full SNMP functionality with all important standard and private MIBs. Thus, all authorized SNMP network management stations can make configuration changes. Inband as well as Outband management is supported. The ATM MultiSwitch is configurable for most every network application...Reasonable in price and modular architecture... a wide range of applications. By using 2 ATM rings with its two ATM ports, the ATM MultiSwitch can provide line redundancy and higher network stability.
Flexibility with regard to applicable ATM interfaces makes it suitable for switching public ATM networks as well as private ATM backbone structures.
The ATM MultiSwitch is particularly effective as an access device for Metropolitan Area Networks (MANs.) It can be used as an active node in the network to provide the customer with an Ethernet or ISDN interface, or as an ATM access device for customers requiring a more powerful means of access - the ATM MultiSwitch is the appropriate system in any case. SoftwareFlexible and conforms to standards...
Full-LAN emulation functionality is guaranteed for Ethernet connections according to ATM forum version 1.0 (version 2.0 in development) as well as UNI/NNI signaling according to Q 2931 and UNI version 3.0 or 3.1 (version 4.0 in development). LAN emulation functions such as LES, BUS and LECS are also provided.
Optional support of MPOA meeting ATM Forum requirements is in the planning phase and will be realized in the 2nd software generation.
In phase 1, CES (Circuit Emulation Services) will be provided for E1/T1 applications meeting the specifications defined in the VTOA workshop (voice and telephony over ATM) of the ATM Forum. Succeeding generations will integrate B-ISDN and N-ISDN for voice services under VTOA with ATM trunking for narrowband services. This will allow an even more flexible and efficient use of E1/T1 channels. ATM MultiSwitch CellpacksData Sheet
Switched Ethernet Type: 10/100BaseT, autodetect Standard: IEEE 802.3x (10BaseT/100BaseT4) Number of ports: 2 Connector: RJ45
System parameters Processor: i960Jx 33 MHz System bus width: 8/16/32 bit Program memory: 8 MB FLASH, in-circuit prog. Main memory max.: 32 MB Battery backup RAM max.: 512 KB
E1 Type: 2 Mbps, G.703/G.704 Standard: ISO/IEC 8877 Number of ports: 2 Connector: RJ45, 120 ohm
Extension interface Technology: TranSwitch CellBus Data bus width: 32 bit Data rate: > 1 Gbps
Module parameters Weight: 2.5 kg Relative humidity: + 30% bis + 80% Operating temperature: + 5ƒC bis + 50ƒC Operating voltage: +5 VDC Current consumption: 8 A (typical) Chassis: 19" Rack, 1RU
Pricing and Ordering Information 25/155 Mbps ATM-based MultiSwitch for 20/xxxx or 155/xxxx Series Description | SKU # | Price |
---|
Integrated ATM/Ethernet Switch with 2 Uplink Ports (ATM 155 or 25, SONET/SDH, E3, T3, E1, T1, ADSL), 2 x 10/100 Ethernet Ports (Auto-negotiate) and 2 x E1/T1 Ports | x/xxx-x/xxx-ATM-MUX | Call | Integrated ATM/Ethernet Switch with 2 Uplink Ports (ATM 25 or 155, SONET/SDH, E3, T3, E1, T1, ADSL), 2 x 10/100 Ethernet Ports (Auto-negotiate) and 8 x E1/T1 Ports | x/xxx-x/xxx-ATM-MUX-E1/T1 | Call |
Additional Tele and Data Communications Hardware for Mono/MultiLink Systems TDM-based multiplexer solutions for 20/xxxx series Description | SKU # | Price | E1/T1 Fiber Optic Modem | FHT-E1 or T1-ST-MM-850-RJ45-xxx | Call | LightHouse Multiplexer (up to 4 E1/T1) | LH-E1orT1-Y-ST-MM-850-RJ45-xxx | Call | LANMUX (full-duplex Ethernet/10BaseT and up to 4 E1/T1) | LANMUX-10BASET-E1 or T1-Y-ST-MM-850-xxx | Call |
TDM-based multiplexer solutions for 155/xxxx series Description | SKU # | Price | E3/T3 Fiber Optic Modem | FHT-E3 or T3-ST-MM-1300-BNC-xxx | Call | OptoMux Multiplexer EMUX series (fixed 16 x T1/E1), 19" rackmountable and manageable system. Rack base system. | EMUX-T1 or E1-ST-MM-1300-RJ45-xxx | Call | OptoMux Multiplexer FME series (universal protocol multiplexer solution with 6 x T1/E1, Ethernet, V.35), 19" rackmountable and manageable system. Stackable up to 4 units. Rack base system. | FME-ST-MM-1300-xxx | Call | E1 interface module for FME series | IM-FME-G.703-E1 | Call | T1 interface module for FME series | IM-FME-G.703-T1 | Call | Ethernet interface module for FME series | IM-FME-10BaseT | Call | V.35 interface module for FME series (DB-25) | IM-FME-V.35-DB25 | Call | V.35 interface module for FME series (Winchester) | IM-FME-V.35-WIN | Call | X.21 interface module for FME series | IM-FME-X.21 | Call | HDSL interface module for FME series | IM-FME-HDSL | Call |
xxx denotes voltage. Specify 110 or 220 VAC. 12 to 72 VDC available on special request. Other network interfaces available on special request.
|